How to print with PETG Filament?

How to print with PETG Filament?  eolas-prints

PETG filament is a variant of the widely used PET polymer, its use in 3D printing is booming due to the fact that the ratio between printing difficulty and mechanical characteristics is very good. It is widely used in industry because it is chemically very stable and has a high impact resistance.


  • Good mechanical properties: it is a material with high impact resistance, great durability and its resistance to temperature is above 80ºC, which is when the material starts to deform.
  • Food grade approval and ability to be sterilised: FDA certification (US agency responsible for the regulation of food, drugs and cosmetics).
  • Chemical resistance: as a very stable material, PETG is chemically resistant to both acid and base attack.
  • Transparency: PETG without dyes (natural) allows 90% of light to pass through, making it the ideal material for making translucent or transparent parts.
  • It is recyclable.
  • It does not produce odour when printed.


  1. Finding the "sweet spot" of the filament is the biggest drawback of this material, obtaining the correct printing parameters.
  2. Need of hot bed for proper adhesion.
  3. Loss of colour due to long term exposure to the sun. UV rays can generate a discolouration of the piece and make it more brittle. To solve this problem we have a PETG that is resistant to this discolouration.

Printing parameters

Extrusion temperature

The temperature range for printing with PETG is between 220°C and 250°C, and the ideal temperature is primarily dependent on the size of the nozzle and the extrusion equipment. In case your 3D printer has a Teflon barrel, you should not raise the temperature above 235°C to avoid deterioration of the barrel. Very high temperature levels will cause the filament to drip, resulting in the "stringing" effect. Very low temperature may cause the extruder to lose steps, resulting in poor material flow. A temperature test must be performed to determine the correct temperature.

Printing surface

A hot bed between 70°C and 90°C is required for proper adhesion with this material. Any specialty adhesive for 3D printing will be helpful in avoiding the notorious 'warping' effect; we therefore recommend these adhesives for large components. If you are printing on a smooth PEI surface, a barrier must be created between the PEI and the part using an adhesive (glue stick or lacquer), or it will be difficult to remove the part from the surface.

Printing speed

The speed of a 3D printer is very dependent on the whole set of parts that make up the printer, but having some sort of benchmark value is helpful. The optimal speed for most cases would be between 25mm/s and 55mm/s.

Layer fan

Using a layer fan is not required with PETG filament, but it is helpful if the part has a lot of detail or a lot of overhangs to improve adhesion between layers. If the part begins to delaminate or crack, reduce the layer fan speed (set it above 20%) to reduce airflow and increase adhesion between layers.

Layer height

The optimum layer height is usually 50% of the nozzle outlet diameter, but it can be lowered to 25% or raised to 75-80%. For a 0.4mm nozzle, an optimum layer height would be 0.2mm within a range of 0.1mm and 0.3mm.


It's crucial to determine the precise value for each material's dimensional tolerance in order to set this parameter. During regular printing, this parameter should not vary by more than 5%, i.e. 95% to 105%. If our extruder is badly calibrated after we conduct a flow test, we must first calibrate it to obtain optimal outcomes.


The retraction factor is dependent on the hotend-extruder assembly and must be determined through a retraction test. The initial values can be as follows

  • Direct drive: 1-2 mm & 25 mm/s
  • Bowden: 5-6 mm & 30 mm/s

Reading next

How to print with NatureWorks INGEO PLA Filament?  eolas-prints
How to print with PLA Filament?  eolas-prints