IDEX vs Dual Nozzle vs Toolchanger: Which Multi-Extruder Setup for Large-Format Printing?

Article author: Eolas Prints
Article published at: Nov 17, 2026
Article tag: Bambu Lab Article tag: Bambu Lab H2D Article tag: Buyer's Guide Article tag: Comparison Article tag: CreatBot Article tag: Elegoo Article tag: Elegoo OrangeStorm Giga Article tag: IDEX Article tag: large-format Article tag: Large-Format 3D Printers Article tag: Mingda Article tag: Mingda MD-400D Article tag: Multi-Material 3D Printing Article tag: Prusa Article tag: Prusa CORE One L+ INDX Article tag: Prusa XL Article tag: Tool Changer
Mingda MD-400D IDEX large-format 3D printer with two independent print heads

Updated: 16 November 2026

Short answer: an IDEX 3D printer has two print heads on separate carriages, so it prints two copies (or a mirrored left/right pair) at once. On the Mingda MD-400D that is two parts up to 200 mm wide in copy mode or 160 mm in mirror mode, roughly halving machine time for a batch. Two nozzles on one head (CreatBot HS, Bambu Lab H2D, Mingda MD-600D/MD-1000D) cannot print two parts at once but suit model plus support in one large part. Toolchangers (Prusa XL, CORE One L+ INDX) suit 4–8 colours or materials, and the Elegoo OrangeStorm Giga can take extra heads to print up to four copies.

"Dual extruder" covers very different machines. Below: the four layouts, what each does to throughput and part size, a decision table and prices. If you need one large part in one material, any machine in our large-format 3D printers range will do.

Four ways to put more than one nozzle on a large printer

Layout How it works Prints two parts at once? Machines we sell
IDEX (independent dual extruder) Two heads on two carriages that move independently along X. One can park while the other prints, or both print at the same time. Yes: copy and mirror modes Mingda MD-400D
Two nozzles on one head Both nozzles share one carriage. The idle nozzle lifts (CreatBot, Bambu) or simply sits next to the active one. No CreatBot D400 HS, D600 Pro 2 HS, D600 Pro3 HS, D1000 Pro HS; Mingda MD-600D, MD-1000D; Bambu Lab H2D
Toolchanger One motion system picks up one of several parked tools. Only one tool prints at a time. No Prusa XL (1, 2 or 5 tools), Prusa CORE One L+ INDX (4 or 8 tools)
Multi-head batch Extra heads fixed side by side on the same X axis. All heads print the same job together. Yes: up to four identical models Elegoo OrangeStorm Giga

The machines, one sentence each:

  • The Mingda MD-400D is a 400 × 400 × 400 mm IDEX printer with two 350 °C extruders and an enclosed (not heated) frame, priced at €4,124 incl. VAT (€3,408 ex VAT); it is the only IDEX printer in our range.
  • The Mingda MD-600D (600 mm cube, €21,249 incl. VAT / €17,561 ex VAT) and MD-1000D (1000 mm cube, €38,749 / €32,024 ex VAT) carry dual 350 °C extruders on one printhead: not IDEX, so no copy or mirror mode.
  • The CreatBot D400 HS is a 420 × 400 × 420 mm printer with two auto-raising 420 °C nozzles on one head, a 70 °C actively heated chamber and 90 mm³/s hot ends, priced at €6,895 incl. VAT (€5,698 ex VAT). The D600 Pro 2 HS (600 mm cube, 70 °C chamber, €15,999 / €13,222 ex VAT), D600 Pro3 HS (620 mm cube, 80 °C chamber, €21,249 / €17,561 ex VAT) and D1000 Pro HS (1050 mm cube, 80 °C chamber, €47,499 / €39,255 ex VAT) use the same dual-nozzle layout.
  • The Bambu Lab H2D has two nozzles on one toolhead (the left one lifts), a 65 °C actively heated chamber and 325 × 320 × 325 mm per nozzle (350 mm wide using both), from €2,045.99 incl. VAT (€1,690.90 ex VAT).
  • The Prusa XL is a 360 × 360 × 360 mm toolchanger with up to five independent toolheads, from €2,399 (1 tool) to €4,099 (5 tools) incl. VAT. Eolas Prints is an official Prusa Research reseller.
  • The Prusa CORE One L+ INDX is a 298 × 275 × 330 mm toolchanger with 4 or 8 tools and a 60 °C heated chamber, at €2,529 (4T) or €2,779 (8T) incl. VAT.
  • The Elegoo OrangeStorm Giga is an 800 × 800 × 1000 mm open-frame printer with a 300 °C nozzle and a four-zone heated bed, priced at €2,779 incl. VAT (€2,297 ex VAT); Elegoo states that three additional printheads can be added on the X axis to print four copies of a model at once.
Mingda MD-400D IDEX large-format 3D printer with two independent print heads

Copy mode and mirror mode: the maths

IDEX earns its price in two modes:

  • Copy (duplication) mode: both heads print the same G-code side by side on a bed split along X: on the MD-400D, parts up to 200 mm wide, 400 mm deep and 400 mm tall.
  • Mirror mode: the second head prints a mirror image, giving a left and a right part per job. The heads move towards each other, which costs width: up to 160 mm per part on the MD-400D.

Both heads extrude at once, so a copy or mirror job takes about as long as one part and gives you two: a batch needs about half the machine time. Heating, levelling, part removal and failed jobs still cost time, so the real saving is a little under 50 %.

IDEX does not make a single part faster, and parts wider than 200 mm rule out copy mode. Plating several parts on one bed is not the same thing: a single head prints them one after another, so four parts take four times as long.

Eolas worked example: machine time for 24 identical parts

Assumption: a part that takes 10 hours on one head and fits each machine's copy limits, at the same speed per head on every machine.

Layout (example machine) Heads printing at once Parts per job Jobs for 24 parts Machine time
Single nozzle, or two nozzles on one head (CreatBot HS, MD-600D) 1 1 (or several plated, printed in turn) 24 (or fewer, longer jobs) ≈ 240 h
Toolchanger (Prusa XL, INDX) 1 1 24 ≈ 240 h
IDEX copy or mirror mode (MD-400D) 2 2 12 ≈ 120 h
Multi-head, 4 heads (Giga with three extra heads) 4 4 6 ≈ 60 h*

How we calculated it: machine time = 24 parts × 10 h ÷ heads printing at once. It ignores warm-up, part removal and failures. *Elegoo does not publish the usable width per head in four-head mode; each copy has to fit within its share of the 800 mm X axis, so confirm the limit for your part with us before planning on it.

Material cost per part does not change: with Eolas 1.75 mm PLA at €19.90/kg incl. VAT, a 250 g part costs about €4.98 however many heads print it.

Productivity compared: part size, waste, change time and risk

IDEX (MD-400D) Two nozzles on one head (CreatBot HS) Toolchanger (INDX / XL) Multi-head (Giga)
Max part, one material 400 × 400 × 400 mm (15.7 in cube) 420 × 400 × 420 mm (16.5 × 15.7 × 16.5 in, D400 HS) up to a 1050 mm cube (41.3 in, D1000 Pro HS) 298 × 275 × 330 mm (11.7 × 10.8 × 13.0 in, INDX); 360 mm cube (14.2 in, XL) 800 × 800 × 1000 mm (31.5 × 31.5 × 39.4 in, one head)
Max part, two materials 400 mm wide (heads take turns) Narrower by the nozzle spacing, e.g. 365 mm instead of 420 mm on the D400 HS (CreatBot) Most of the volume Not a multi-material layout
Parts per job (identical) 2 (up to 200 mm wide each); mirrored pair up to 160 mm 1 1 Up to 4
Material change Head swap; idle head parks off the part Nozzle swap; idle nozzle lifts and, on CreatBot, a shutter closes it Prusa states ≈ 12 s and ≈ 0.013 g per change on INDX; XL "swaps the entire head in seconds" Not applicable
If one part fails Usually stop the whole job in copy/mirror One part, one job One part, one job Usually stop the whole job
Chamber Enclosed, not heated Actively heated 70–80 °C INDX 60 °C heated; XL open (enclosure optional) Open frame

Sources: Mingda MD-400D specification as published by Mingda and resellers; CreatBot D400 HS, D600 Pro3 HS and D1000 Pro HS product pages; Prusa INDX and Prusa XL product pages; Elegoo OrangeStorm Giga product page; Bambu Lab H2D wiki. Checked 16 November 2026.

In practice, a print with 200 colour changes works out at about 40 minutes of changes and 2.6 g of waste (about €0.05 of PLA) on Prusa's INDX figures, against about 140 minutes at the 42 s per swap Prusa quotes for single-nozzle systems. Toolchangers win on multi-colour work and bring nothing to single-colour batches.

Two materials and soluble supports

IDEX, dual-nozzle and toolchanger machines can all print a model material with a water-soluble (PVA, BVOH) or breakaway support. The differences:

  • IDEX parks the idle head at the side, so it cannot drip on or drag across the part: clean two-material prints across the full 400 mm on the MD-400D, and Mingda lists PVA among its materials.
  • Two nozzles on one head is simpler and makes the biggest dual-material parts, up to about 1 m on the CreatBot D1000 Pro HS. CreatBot lifts the idle extruder and closes a shutter over it; on the H2D a flow blocker seals the idle nozzle.
  • Toolchangers keep each material in its own nozzle (no cross-contamination, almost no purge) but in a smaller volume.

CreatBot HS machines add a feature for 100-hour prints: if nozzle 1 runs out of filament, the printer switches to nozzle 2 and carries on. On a metre-scale (meter-scale) part, such as a mould (mold) pattern that has already run for three days, that can save the job. Dry PVA and nylon first: see our filament drying guide.

Calibration: keeping two nozzles aligned

Every multi-nozzle machine must know each nozzle's exact offset, or the second material lands in the wrong place:

  • CreatBot HS (D400 HS, D600 Pro3 HS, D1000 Pro HS): XY offset measured by an HD camera, Z by sensors.
  • Bambu Lab H2D: a calibration coil on the bed plus the toolhead camera.
  • Prusa INDX: a tool-offset sensor reads each tool in about 15 s, Prusa states.
  • IDEX (MD-400D): align both carriages in X, Y and Z at commissioning and after nozzle changes; our training and support covers it.

Which layout should you choose? Decision table by job

Your job Choose Why
Batches of identical parts up to 200 mm wide in PLA, PETG, ABS or ASA Mingda MD-400D Two parts per job, about half the machine time.
Left/right pairs up to 160 mm wide (brackets, trims, housings) Mingda MD-400D Mirror mode prints both hands in one job.
Many copies of PLA/PETG parts at the lowest machine cost Elegoo OrangeStorm Giga + extra heads Up to four copies per job; open frame, so not for ABS or nylon.
One large part with soluble support in PA-CF, PC or ABS CreatBot D400 HS, D600 Pro3 HS or D1000 Pro HS 420 °C nozzles, 70–80 °C heated chamber, backup nozzle.
600 mm or 1 m parts with model + support in PLA, PETG or ASA Mingda MD-600D or MD-1000D Dual 350 °C extruders, enclosed frame, no heated-chamber premium.
4–8 colours or materials in one part Prusa XL 5-tool or CORE One L+ INDX 8-tool Almost no purge, fast changes.
Two materials in parts up to about 325 mm, on a small budget Bambu Lab H2D Two nozzles, 65 °C heated chamber.

Compare machines on our comparison page, browse multicolour and multi-material printers, or read about the Bambu Lab H2D vs H2S, the Prusa CORE One vs CORE One L vs XL, how a 9-tool changer works and toolchanger vs filament-swap multicolour.

Prices and how to buy from Eolas Prints

Machine Layout Price incl. 21 % VAT Price ex VAT How to buy
Elegoo OrangeStorm Giga Single head, up to 4 heads €2,779 €2,296.69 Cart
Bambu Lab H2D / AMS Combo Two nozzles, one head €2,045.99 / €2,279.99 €1,690.90 / €1,884.29 Cart
Prusa XL+ assembled (1 / 2 / 5 tools) Toolchanger €2,399 / €3,099 / €4,099 €1,982.64 / €2,561.16 / €3,387.60 Cart
Prusa CORE One L+ INDX (4 / 8 tools) Toolchanger €2,529 / €2,779 €2,090.08 / €2,296.69 Cart
Mingda MD-400D IDEX €4,124 €3,408.26 Cart
CreatBot D400 HS Two nozzles, one head €6,895 €5,698.35 Cart
CreatBot D600 Pro 2 HS Two nozzles, one head €15,999 €13,222.31 Quote
CreatBot D600 Pro3 HS Two nozzles, one head €21,249 €17,561.16 Quote
Mingda MD-600D Two extruders, one head €21,249 €17,561.16 Quote
Mingda MD-1000D Two extruders, one head €38,749 €32,023.97 Quote
CreatBot D1000 Pro HS Two nozzles, one head €47,499 €39,255.37 Quote

Prices as at 16 November 2026, in EUR. Ex-VAT = price ÷ 1.21. Visitors outside the EU see prices without Spanish VAT on the product pages, and shipping is quoted separately. Ask us about extra printheads for the Giga.

  • Cart machines: order online; the current lead time is shown next to the price.
  • Quote machines (D600 Pro 2 HS, D600 Pro3 HS, D1000 Pro HS, MD-600D, MD-1000D): price shown; freight, installation and training quoted per project. Contact us with your country and parts.
  • Shipping outside the EU: we ship DAP by default: we deliver to your address and you pay import duties, taxes and customs clearance. If you prefer your own freight forwarder, EXW collection from our warehouse in Cantabria, Spain, is available on request. See our shipping policy.
  • Warranty: provided by the manufacturer.

Where the numbers come from. Written by Tanuj Goswami, CTO of Eolas Prints, a filament manufacturer in Reocín, Cantabria (Spain). Specifications: manufacturers' published pages (CreatBot, Elegoo, Prusa, Bambu Lab; Mingda via its published specifications and resellers), checked 16 November 2026. Prices: our store, same date. The worked example and change-time figures are our own arithmetic, explained under each table, not measured benchmarks.

Printing batches of identical parts? The Mingda MD-400D prints two at once.
Buy it online, or get a free consultation on the right multi-head layout for your parts.

See the Mingda MD-400D

Need a quote for a CreatBot or Mingda MD-600D/MD-1000D? Request a quote or book a free consultation.

Frequently asked questions

What is an IDEX 3D printer?

IDEX stands for independent dual extruder: two print heads on separate carriages that move independently. One head can park while the other prints, for clean two-material prints, or both can print at once in copy or mirror mode. The Mingda MD-400D (400 × 400 × 400 mm, €4,124 incl. VAT) is an IDEX printer.

What are copy mode and mirror mode?

In copy mode both heads print the same part side by side, so you get two identical parts per job; on the MD-400D each can be up to 200 mm wide. In mirror mode the second head prints a mirror image, giving a left and a right part per job, each up to 160 mm wide on the MD-400D.

Is IDEX better than a dual nozzle on one head?

For batches of identical parts, yes: only IDEX prints two at once. For one large part with support material, two nozzles on one head is simpler and comes in bigger machines, up to the 1050 mm CreatBot D1000 Pro HS with a heated chamber and backup-nozzle switching.

Does IDEX double print speed?

No. Each head prints at normal speed, so one part takes as long as on a single-head printer. IDEX doubles parts per job in copy or mirror mode, cutting batch machine time by a little under half.

What's the difference between IDEX and a toolchanger?

IDEX has two heads that can print at the same time. A toolchanger such as the Prusa XL (up to 5 tools) or CORE One L+ INDX (4 or 8 tools) has more tools, but only one prints at a time. Choose IDEX for doubling batch output and a toolchanger for many colours or materials in one part. Prusa states INDX changes take about 12 s and waste about 0.013 g.

Can the Elegoo OrangeStorm Giga print with several heads at once?

Yes. Elegoo states that three additional printheads can be added on the X axis to print four copies of a model, or one model in four colours, at once. Elegoo does not publish the usable width per head, so check with us that your part fits.

Which IDEX printer has the largest build volume you sell?

The Mingda MD-400D, with 400 × 400 × 400 mm in single mode, 2 × 200 mm wide in copy mode and 2 × 160 mm wide in mirror mode. It is the only IDEX printer in our range. For bigger dual-material parts, the Mingda MD-600D/MD-1000D and CreatBot HS machines use two nozzles on one head, up to a 1050 mm cube.

Share