Updated: 16 November 2026
Short answer: PLA, PETG and TPU print well on an open-frame large printer such as the Elegoo OrangeStorm Giga (800 × 800 × 1000 mm, €2,779 incl. VAT). Large ABS and ASA parts need at least an enclosure, and the bigger the part, the more you need an actively heated chamber. Nylon (PA), PC and carbon-fibre composites need an actively heated chamber: the CreatBot HS range holds 70 °C (D400 HS, D600 Pro 2 HS) or 80 °C (D600 Pro3 HS, D1000 Pro HS), starting at €6,895 incl. VAT for the D400 HS.
Below: the three chamber architectures, the chamber of 13 machines from €1,899 to €47,499, and what each material needs when parts get long: moulds (molds in US English), housings, jigs and fixtures. All machines are on our large-format 3D printers page.
Open frame, passive enclosure, heated chamber: three architectures
Open frame. The part sits in room air and each layer cools as soon as the nozzle moves on. Ideal for PLA, fine for PETG and TPU.
Passive enclosure. Panels keep draughts off and trap some heat from the bed. On a large frame there is a lot of air to warm: Prusa XL owners on Prusa's forum report enclosure readings from the mid-30s to the mid-40s °C. It helps ABS and ASA and lets a filter catch fumes, but it cannot hold a set temperature.
Actively heated chamber. A heater and fan hold a set temperature from the first layer to the last. That is what engineering materials need, and why these machines cost more and draw more power.
Why chamber temperature matters more on big parts
Each layer shrinks as it cools, in proportion to its length: a 600 mm layer tries to shrink three times as much as a 200 mm one. The layers below are cooler and stiffer, so the difference becomes stress that lifts corners or splits layers. How far an ABS layer tries to shrink as it cools from about 100 °C to the surrounding air:
| Layer length | Open frame (air 25 °C) | Passive enclosure (40 °C) | Heated chamber 70 °C | Heated chamber 80 °C |
|---|---|---|---|---|
| 200 mm | 1.4 mm | 1.1 mm | 0.5 mm | 0.4 mm |
| 400 mm | 2.7 mm | 2.2 mm | 1.1 mm | 0.7 mm |
| 600 mm | 4.1 mm | 3.2 mm | 1.6 mm | 1.1 mm |
| 800 mm | 5.4 mm | 4.3 mm | 2.2 mm | 1.4 mm |
| 1,000 mm | 6.8 mm | 5.4 mm | 2.7 mm | 1.8 mm |
Eolas calculation: shrinkage = length × (100 °C − chamber air) × 90 × 10⁻⁶ per °C, a typical linear expansion coefficient for ABS (published values are roughly 70–100 × 10⁻⁶). The part still shrinks after printing; the chamber reduces the mismatch between the new layer and the part below while it prints, which is what causes warping. A simplified model for comparison, not a prediction for a specific part.
At 600 mm, an open frame asks each ABS layer to absorb about 4 mm of shrinkage; an 80 °C chamber cuts that to about 1 mm. Brims and adhesives help, but on long parts they rarely close that gap. See our guide to fixing ABS and ASA warping.
Chamber type of 13 large and large-desktop 3D printers
Sorted from open frame to the hottest chamber. In short: the Elegoo OrangeStorm Giga is an 800 × 800 × 1000 mm open-frame printer with a 300 °C nozzle and four heated bed zones, priced at €2,779 incl. VAT; the CreatBot D400 HS is a 420 × 400 × 420 mm printer with dual 420 °C nozzles and a 70 °C actively heated chamber with HEPA and carbon filtration, priced at €6,895 incl. VAT; and the CreatBot D600 Pro3 HS is a 620 × 620 × 620 mm printer with dual 420 °C nozzles and an 80 °C actively heated chamber, priced at €21,249 incl. VAT (€17,561 ex VAT).

| Printer | Build volume | Chamber | Max nozzle | Engineering materials the manufacturer lists | Price incl. VAT / ex VAT |
|---|---|---|---|---|---|
| Elegoo OrangeStorm Giga | 800 × 800 × 1000 mm (31.5 × 31.5 × 39.4 in) | Open frame | 300 °C | PA (nylon); also PLA, PETG, TPU | €2,779 / €2,296.69 |
| Prusa XL+ (1 toolhead) | 360 × 360 × 360 mm (14.2 × 14.2 × 14.2 in) | Open; Enclosure bundle is passive, with HEPA filter | 290 °C | ABS, ASA, PA, PC, composites | €2,399 / €1,982.64 (bundle €2,929 / €2,420.66) |
| Mingda MD-400D IDEX | 400 × 400 × 400 mm (15.7 × 15.7 × 15.7 in) | Enclosed, passive (not heated) | 350 °C (320 °C continuous) | PET-CF, PET-GF, HtPA-CF, HtPA-GF, ABS-GF25 | €4,124 / €3,408.26 |
| Flashforge Guider 3 Ultra | 330 × 330 × 600 mm (13.0 × 13.0 × 23.6 in) | Enclosed, pre-heat and air circulation, not actively heated* | 350 °C | ABS, ASA, PA-CF, PAHT-CF, PET-CF, PA12-CF | €4,199 / €3,470.25 |
| Mingda MD-600D | 600 × 600 × 600 mm (23.6 × 23.6 × 23.6 in) | Enclosed, passive (no chamber heater listed) | 350 °C | ABS, ASA, PET-CF, PET-GF, PA-CF, PA-GF | €21,249 / €17,561.16 (quote) |
| Mingda MD-1000D | 1000 × 1000 × 1000 mm (39.4 × 39.4 × 39.4 in) | Enclosed, passive (no chamber heater listed) | 350 °C | ABS, ASA, PET-CF, PET-GF, PA-CF, PA-GF | €38,749 / €32,023.97 (quote) |
| Prusa CORE One L+ | 300 × 300 × 330 mm (11.8 × 11.8 × 13.0 in) | Active, 60 °C | 290 °C | PC; ABS, ASA and PA with the optional Advanced Filtration System | €1,899 / €1,569.42 |
| Prusa CORE One L+ INDX (4 tools) | 298 × 275 × 330 mm (11.7 × 10.8 × 13.0 in) | Active, 60 °C | 300 °C | ASA, PC, PA11 (non-abrasive grades) | €2,529 / €2,090.08 |
| Bambu Lab H2D | 325 × 320 × 325 mm single nozzle (12.8 × 12.6 × 12.8 in) | Active, 65 °C | 350 °C | ABS, ASA, PC, PA, PA-CF, PPA-CF, PPS, PPS-CF | €2,045.99 / €1,690.90 |
| CreatBot D400 HS | 420 × 400 × 420 mm (16.5 × 15.7 × 16.5 in) | Active, 70 °C, HEPA + carbon | 420 °C | ABS, ASA, PC, PA, PA-CF, PC-CF, PET-CF, UltraPA-CF, PPS-CF and more | €6,895 / €5,698.35 |
| CreatBot D600 Pro 2 HS | 600 × 600 × 600 mm (23.6 × 23.6 × 23.6 in) | Active, 70 °C, HEPA + carbon, filament dry room | 420 °C | As D400 HS | €15,999 / €13,222.31 (quote) |
| CreatBot D600 Pro3 HS | 620 × 620 × 620 mm (24.4 × 24.4 × 24.4 in) | Active, 80 °C, HEPA + carbon, dry room | 420 °C | As D400 HS | €21,249 / €17,561.16 (quote) |
| CreatBot D1000 Pro HS | 1050 × 1050 × 1050 mm (41.3 × 41.3 × 41.3 in) | Active, 80 °C, HEPA + carbon, dry room | 420 °C | As D400 HS | €47,499 / €39,255.37 (quote) |
Prices as at 16 November 2026, EUR incl. 21 % Spanish VAT; ex VAT = ÷ 1.21. Outside the EU your local store shows prices without Spanish VAT, and shipping is quoted separately. “Quote”: price shown; freight, installation and training quoted per project. Specifications: manufacturers' published data as listed on our product pages. Eolas Prints is an official Prusa Research reseller and an authorised Flashforge reseller (see why buy Flashforge from an authorised distributor). *Per 3DTechValley's review: “pre-heating and air circulation (not actively heated)”; confirm with us if chamber temperature is critical.
Two things stand out. The only actively heated machines here bigger than about 350 mm in any direction are the four CreatBot HS models. And the Mingda MD-600D and CreatBot D600 Pro3 HS cost the same (€21,249): the Pro3 brings an 80 °C chamber and 420 °C nozzles; the MD-600D an unheated enclosure, 350 °C nozzles and 0.6 mm high-flow printing. MD-600D for PLA, PETG and PET-CF; Pro3 for large ABS, PC or nylon.
What each material needs
Nozzle and bed ranges are typical values from filament makers. The chamber and part-size columns are Eolas guidance, not manufacturer specifications. Your filament's datasheet wins.
| Material | Nozzle / bed | Chamber we recommend | Open frame | Passive enclosure | Heated chamber (60–80 °C) |
|---|---|---|---|---|---|
| PLA | 190–240 °C / 35–65 °C | None; keep it cool | Full build volume | Full volume, door or lid open | Not needed; switch the heater off (PLA softens at about 55–60 °C) |
| PETG | 240–270 °C / 60–80 °C | None, or enclosure without heat | Full build volume | Full build volume | Not needed |
| TPU | 200–250 °C / 35–45 °C | None | Full build volume | Full build volume | Not needed |
| ABS | 230–260 °C / 90–120 °C (Eolas ABS) | 45–60 °C; hotter for long parts | Small parts only; long parts lift and crack | Small to medium parts | Full build volume |
| ASA | 240–260 °C / 90–110 °C | 45–60 °C; hotter for long parts | Small parts only | Small to medium parts | Full build volume |
| PC | 260–290 °C / 100–120 °C | 60 °C or more | Not recommended | Small parts | Medium to large parts; 70–80 °C is better |
| PA, PA-CF (nylon) | 260–300 °C / 100–120 °C | 60 °C or more for large parts; always dry | Small parts in low-warp grades | Small to medium parts | Full build volume |
| PET-CF | 260–300 °C / 80–120 °C | Enclosure; heated for large parts | Small parts | Medium parts | Full build volume |
| PPS-CF | 310–350 °C / 100–120 °C | The hottest available | Not recommended | Not recommended | On 350 °C+ machines with a hardened nozzle |
Sources: Bambu Lab filament guide material table (nozzle ±10 °C, bed for PEI plates) for PLA, PETG, TPU, PC, PA, PET-CF and PPS-CF; Eolas datasheets for ABS; our ASA printing guide (ASA temperatures) and ABS printing guide (the 45–60 °C chamber figure). Carbon- and glass-fibre filaments are abrasive: use a hardened or wear-resistant nozzle and confirm which nozzle ships with your machine. For PEEK, PEI and other materials that need more than 80 °C, see our Prusa Pro HT90 high-temperature filament guide.
Nylon and PC absorb moisture, and wet filament prints weak parts in any chamber. The D600 Pro 2 HS, D600 Pro3 HS and D1000 Pro HS have a filament dry room; otherwise see our filament drying guide. Shop high-temperature filament and engineering and composite filament.
Can you print ABS on the Elegoo OrangeStorm Giga?
Elegoo lists PLA, PETG, TPU and PA (nylon) for the Giga, not ABS or ASA, and we would not plan large ABS parts on it. Its open 800 × 800 × 1000 mm frame invites exactly the long parts that warp most: an 800 mm ABS layer in 25 °C air tries to shrink about 5.4 mm. What works instead:
- PETG for big parts. It shrinks far less than ABS. For outdoor parts, instead of ASA, use our certified UV-resistant PETG (€30.50 per 1 kg incl. VAT).
- Small ABS/ASA parts only, with a brim, no draughts and minimal cooling.
- No improvised enclosure around a 1.4 m frame without considering the motors and electronics inside; check how modifications affect the manufacturer's warranty.
- A heated chamber if ABS, ASA, PC or nylon are your main materials: the CreatBot D400 HS (€6,895) is add-to-cart.
At €2,779, the Giga is the most build volume per euro for PLA, PETG and TPU. Buy it for that.

Fumes and filtration
Melting ABS and ASA releases styrene-based fumes and ultrafine particles, and a large printer melts more plastic per hour than a desktop one.
- CreatBot D400 HS, D600 Pro 2 HS, D600 Pro3 HS and D1000 Pro HS: HEPA and activated-carbon filtration listed as standard.
- Flashforge Guider 3 Ultra: HEPA 13 and activated carbon, with internal and external circulation. Bambu Lab H2D: activated carbon and HEPA.
- Prusa XL+ Enclosure bundle: HEPA filtration. Prusa CORE One L+: Prusa lists ABS, ASA, HIPS and PA with the optional Advanced Filtration System.
- Elegoo Giga and Mingda MD series: no filtration listed. Print in a well-ventilated room, or extract the air outside.
In Gulf workshops at 35–45 °C in summer, warm air helps against warping but hurts electronics and part cooling. Use an air-conditioned room and let the chamber, not the weather, set the temperature.
How much electricity does a heated chamber use?
CreatBot rates the D600 Pro3 HS at 2,500 W for the printer plus 3,000 W for chamber heating, and the D1000 Pro HS at 6,000 W plus 6,000 W. Ceilings at full rated power and an example tariff of €0.20 per kWh:
| Printer | Rated power (of which chamber) | Max cost per hour | Max cost, 24-hour job | Current at 230 V |
|---|---|---|---|---|
| Elegoo OrangeStorm Giga | 1,530 W (no chamber) | €0.31 | €7.34 | 6.7 A |
| Mingda MD-1000D | 3,100 W (no chamber heater) | €0.62 | €14.88 | 13.5 A |
| CreatBot D400 HS | 3,200 W (chamber share not listed) | €0.64 | €15.36 | 13.9 A |
| CreatBot D600 Pro 2 HS | 5,500 W at 240 V (chamber share not listed) | €1.10 | €26.40 | 22.9 A at 240 V |
| CreatBot D600 Pro3 HS | 5,500 W (3,000 W chamber) | €1.10 (chamber ≤ €0.60) | €26.40 (chamber ≤ €14.40) | 23.9 A |
| CreatBot D1000 Pro HS | 12,000 W (6,000 W chamber) | €2.40 (chamber ≤ €1.20) | €57.60 (chamber ≤ €28.80) | about 52 A |
Calculated as rated kW × €0.20, and watts ÷ 230 V for current. Heaters cycle once at temperature, so real use is usually lower.
The supply matters more than the bill. A UK or Gulf 13 A plug tops out at about 2,990 W, so the D400 HS, both D600 HS models, the D1000 Pro HS and the MD-1000D need a dedicated circuit sized by your electrician; for the D1000 Pro HS, confirm single- or three-phase with us before ordering. Printing PLA or PETG? Switch the chamber heater off.
Which one should you choose?
- Only PLA, PETG and TPU, parts up to 1 m tall? An open frame is enough. The Elegoo OrangeStorm Giga (€2,779) gives you 800 × 800 × 1000 mm.
- Mostly PLA/PETG, some PET-CF, and you want dust and noise contained? A passive enclosure: the Mingda MD-400D (€4,124, IDEX), or the MD-600D and MD-1000D for 600 mm and 1 m parts.
- ABS, ASA, PC or nylon in parts up to about 330 mm? A desktop-size heated chamber: Bambu Lab H2D (65 °C, €2,045.99) or Prusa CORE One L+ (60 °C, €1,899).
- Engineering materials in parts up to 420 mm? The CreatBot D400 HS: 70 °C chamber, 420 °C nozzles, €6,895, add to cart.
- Engineering materials in parts of 600–620 mm? The D600 Pro 2 HS (70 °C, €15,999) or D600 Pro3 HS (80 °C, €21,249). Choose the Pro3 for the longest ABS, PC and PA-CF parts.
- Engineering parts close to 1 m? The CreatBot D1000 Pro HS (1050 mm cube, 80 °C, €47,499), once your power supply is confirmed.
More detail: Bambu Lab H2D vs H2S, Prusa CORE One vs CORE One L vs XL, and, for high volumes, our pellet 3D printer buying guide (the PioCreat MS01 has a 100 °C chamber).
Buying from Eolas Prints
- Add to cart: Elegoo Giga, CreatBot D400 HS, Mingda MD-400D, Prusa, Bambu Lab and Flashforge. The current lead time is shown next to the price.
- By quote: CreatBot D600 Pro 2 HS, D600 Pro3 HS, D1000 Pro HS, Mingda MD-600D and MD-1000D. Price shown; freight, installation and training quoted per project; lead time confirmed with your quote.
- Outside the EU: we ship DAP by default: we deliver to your address; you pay import duties, taxes and clearance. EXW collection from our warehouse in Cantabria, Spain, is available on request if you prefer your own freight forwarder. See our shipping policy.
- Warranty: provided by the manufacturer.
Not sure your part needs a heated chamber?
Send us the part size and material. We'll tell you which chamber you need and quote the machine, freight and installation.
Prefer to talk it through? Book a free consultation.
Where the numbers come from. Written by Tanuj Goswami, CTO of Eolas Prints, a filament manufacturer in Reocín, Cantabria (Spain) that makes PLA, PETG, ABS, ASA and TPU filament and supplies the printers in this guide. Sources: manufacturers' specifications as listed on our product pages on 16 November 2026; the Bambu Lab filament guide and our own datasheets for print temperatures; Prusa XL owner reports on Prusa's forum for passive-enclosure temperatures; 3DTechValley's Guider 3 Ultra review. Shrinkage and electricity figures are our calculations (method under each table). Chamber and part-size recommendations are Eolas guidance, not manufacturer specifications.
Frequently asked questions
Do I need a heated chamber to print ABS?
For small ABS parts, a closed enclosure is usually enough; our ABS guide recommends 45–60 °C. For large parts, yes in practice: shrinkage grows with length, and passive enclosures on big frames often stay at 35–45 °C. The CreatBot D400 HS (420 × 400 × 420 mm, 70 °C actively heated chamber, €6,895 incl. VAT) is the entry point.
What chamber temperature does nylon (PA-CF) need?
Our guidance is 60 °C or more for large PA and PA-CF parts, with a 260–300 °C nozzle, a 100–120 °C bed, dry filament and a hardened nozzle. Suitable machines: Bambu Lab H2D (65 °C), CreatBot D400 HS and D600 Pro 2 HS (70 °C), D600 Pro3 HS and D1000 Pro HS (80 °C).
Is an enclosure the same as a heated chamber?
No. A passive enclosure keeps draughts out and traps some bed heat, typically 35–45 °C on large printers, but cannot hold a set temperature. An actively heated chamber has its own heater and fan and holds 60–80 °C on the machines in this guide. The Mingda MD series is enclosed but not heated; the CreatBot HS range is actively heated.
Can the Elegoo OrangeStorm Giga print ABS or ASA?
Elegoo lists PLA, PETG, TPU and PA for the Giga, not ABS or ASA. Small ABS or ASA parts can work with a brim in a draught-free room, but large parts will warp on its open frame. For big outdoor parts use UV-resistant PETG; for large ABS or ASA parts choose a heated-chamber printer.
Why do large ABS parts crack or warp?
Each layer shrinks as it cools, in proportion to its length, while the layers below are already stiff. By our calculation, a 600 mm ABS layer tries to shrink about 4.1 mm cooling from 100 °C to 25 °C air, but about 1.1 mm in an 80 °C chamber. That stress lifts corners or splits layers.
Which large 3D printer is best for carbon-fibre filament?
Choose by part size within the CreatBot HS range: D400 HS up to 420 mm, D600 Pro 2 HS or Pro3 HS for 600–620 mm, D1000 Pro HS up to 1050 mm. All have dual 420 °C nozzles, a 70–80 °C heated chamber and HEPA plus carbon filtration, and CreatBot lists PA-CF, PC-CF, PET-CF and PPS-CF. Use a hardened nozzle.
Does a heated chamber use a lot of electricity?
It is the largest single load. On the CreatBot D600 Pro3 HS, 3,000 W of 5,500 W is chamber heating: at most €0.60 an hour at an example €0.20 per kWh. On the D1000 Pro HS it is 6,000 of 12,000 W, at most €1.20 an hour. Real use is lower, but these machines need a dedicated circuit, not a 13 A plug.