How to print with PETG Filament?

PETG sits between PLA and ABS: tougher and more heat- and chemical-resistant than PLA, but far easier to print than ABS. Here's how to get strong, clean prints with Eolas Prints PETG.

PETG is the material that fills the gap between easy-printing PLA and engineering-grade ABS. It offers significantly better impact resistance and temperature tolerance than PLA, with far less warping and printing difficulty than ABS. For functional parts, kitchen accessories, chemical-resistant components, and anything that needs to outlast PLA, PETG is the first choice.

Key Properties

Heat deflection temperature	62°C
Tensile strength	40–50 MPa
Density	1.27 g/cm³
Shrinkage	Virtually zero
Food contact safe	Yes
Chemical resistance	Excellent (oils, cleaning agents, mild solvents)
UV resistance	Moderate (UV Resistant variant: certified excellent)
Moisture sensitivity	High — dry before use
Diameter tolerance	±0.05 mm

Recommended Print Settings

Nozzle temperature	230–245°C
Bed temperature	70–90°C
Print speed (standard printers)	20–80 mm/s
Print speed (Bambu Lab / high speed)	Up to 150–200 mm/s with tuned profiles
Cooling fan	50–70% (lower than PLA)
Enclosure	Not required, helpful for large parts
Diameter tolerance	±0.05 mm

PETG runs beautifully on modern high-speed CoreXY machines. If you're choosing a printer that will handle PETG at speed, our complete Bambu Lab buyer's guide covers which models suit functional-material printing best.

Drying PETG Before Printing

PETG is highly hygroscopic — it absorbs moisture from the air faster than PLA, and printing with wet PETG causes stringing, surface rough texture, popping during extrusion, and poor layer bonding. This is the single most common cause of poor PETG results.

• Dry at 65–70°C for 4–6 hours before printing if exposed to air for more than a few days
• Store in sealed containers or resealable bags with silica gel desiccant
• A filament dry box feeding directly to the printer is ideal for PETG in humid climates

Bed Adhesion

PETG adheres strongly — sometimes too strongly. The key is preventing it from bonding permanently to your bed surface.

• PEI sheets: Apply a very thin layer of glue stick or hairspray before printing. Bare PEI at high bed temperatures can bond so permanently to PETG that the print tears the PEI surface on removal. Never print PETG directly on bare PEI above 80°C without a release layer.
• Glass: Apply a thin layer of glue stick. Works reliably and gives a smooth first layer.
• Textured PEI: Generally safe for PETG without a release agent at 70–75°C — the texture provides adhesion without flat-surface bonding risk. Check your printer's recommendation.

Printing Transparent and Clear PETG

PETG is naturally near-transparent in its base form — ideal for light diffusers, display cases, and backlit components. To maximise clarity:

• Use a higher nozzle temperature (240–245°C) for better layer fusion
• Reduce cooling fan to 20–40% to allow layers to meld fully
• Increase infill overlap percentage to reduce internal voids
• Print slowly (20–40 mm/s) for maximum transparency
• Dry the filament thoroughly — moisture causes milky cloudiness in clear PETG

Common Issues and Fixes

Stringing

PETG strings more than PLA. Dry the filament first — most stringing is caused by moisture. Then increase retraction distance (4–6mm for Bowden, 1.5–3mm for direct drive) and speed, reduce travel speed, and try enabling combing mode. A temperature tower helps find the sweet spot where stringing minimises without sacrificing layer adhesion.

Layer Adhesion Problems

Increase nozzle temperature by 5°C and reduce cooling fan speed. PETG needs more heat and less cooling than PLA for strong inter-layer bonding. This is the most common trade-off — more cooling gives better overhangs; less cooling gives stronger layers.

Bed Adhesion Too Strong (Print Won't Release)

Let the bed cool fully to room temperature before attempting removal. If using PEI, add a glue stick release layer next time. Never force a PETG print off a hot PEI bed.

Rough Surface Texture or Popping Sounds

This is wet filament. Dry at 65–70°C for 4–6 hours and retry.

Post-Processing PETG

• Sanding: PETG sands well from 200 grit upward. Wet sanding gives the best surface finish.
• Painting: Accepts acrylic and enamel paints with a plastic primer. No vapour smoothing (unlike ABS).
• Gluing: Cyanoacrylate (super glue), epoxy, and IPA-based adhesives all work well. Ensure surfaces are clean and lightly sanded.
• Drilling and tapping: PETG machines cleanly. Drill slowly at low speed to avoid melting.

Food Safety

Eolas Prints PETG is food contact safe. For food-contact applications, note that layer lines in FDM prints create microscopic crevices where bacteria can accumulate. For items that will be washed repeatedly or used with food, print with tighter layers, use a food-safe coating, or choose solid infill.

Eolas Prints PETG Range

• PETG Filament — standard grade, food safe, virtually zero shrinkage. Available in 1.75mm and 2.85mm in multiple colours.
• PETG UV Resistant — certified UV stable for outdoor applications. Maintains colour and structural integrity after extended sun exposure.
• PETG Transition — gradient colour, UV resistant, made sustainably from manufacturing offcuts. Ideal for outdoor decorative parts.

Frequently Asked Questions

What temperature should I print PETG at?

Print PETG at 230–245°C nozzle temperature with a bed of 70–90°C. Use a higher nozzle temperature (240–245°C) and lower cooling for clear PETG or stronger layers.

Why is my PETG stringing so much?

The most common cause is moisture. Dry the filament at 65–70°C for 4–6 hours, then tune retraction (4–6mm Bowden, 1.5–3mm direct drive) and enable combing.

Why won't my PETG print release from the bed?

PETG bonds very hard to bare PEI. Use a glue-stick or hairspray release layer, never print on bare PEI above 80°C, and let the bed cool fully before removing the print.

Is Eolas Prints PETG food safe?

Yes, it is food-contact safe. Because FDM layer lines can trap bacteria, use solid infill or a food-safe coating for items that are washed repeatedly.

Is PETG or PLA stronger?

PETG has higher impact resistance and heat tolerance than PLA, making it better for functional parts. See our PETG vs PLA comparison guide for a full breakdown.

---

About the author
Sergio Peciña is a qualified Electrical & Electronics Engineer and Eolas Prints' Technical Design Engineer, with over 10 years of experience in 3D printing. He founded the maker spaces at the University of La Rioja and IDIVAL Santander. Every Eolas Prints filament is manufactured in-house in Cantabria, Spain, to ISO 9001 and ISO 14001 standards.

Shop Eolas Prints PETG filament — food safe, made in Spain. Need advice for a project or bulk order? Book a free consultation.