Maîtriser les formes et les combinaisons – Créer des designs fonctionnels

Introduction

The foundation of TinkerCAD design lies in understanding shapes and how they combine. This guide covers the seven essential shapes, their parameters, and how to combine them into functional, printable designs. You'll also learn the critical tolerances and wall thickness requirements that separate successful prints from failures.

The Seven Essential Shapes

1. Cube

• Parameters: Width (X), Depth (Y), Height (Z)
• Best For: Boxes, bases, structural elements
• Print Consideration: Minimum wall thickness 1.5mm for PLA, 2mm for PETG
• Example: A 50mm × 50mm × 10mm cube makes an ideal base platform

2. Cylinder

• Parameters: Radius, Height
• Best For: Posts, tubes, connectors
• Print Consideration: Radius should be at least 3mm for structural integrity
• Example: A cylinder with 5mm radius and 30mm height creates a sturdy vertical post

3. Sphere

• Parameters: Radius
• Best For: Decorative elements, ball joints, connectors
• Print Consideration: Minimum radius 5mm; larger spheres print more reliably
• Example: A 10mm radius sphere can serve as a ball joint in articulated designs

4. Cone

• Parameters: Base Radius, Heiaght
• Best For: Funnels, tapered connectors, decorative tops
• Print Consideration: Steep angles (>45°) may need support structures
• Example: A cone with 8mm base radius and 20mm height creates a tapered connector

5. Torus (Donut)

• Parameters: Major Radius (overall size), Minor Radius (tube thickness)
• Best For: Rings, connectors, decorative elements
• Print Consideration: Minor radius should be at least 2mm
• Example: A torus with 15mm major radius and 3mm minor radius creates a sturdy ring

6. Wedge

• Parameters: Width, Depth, Height
• Best For: Ramps, angled supports, wedges
• Print Consideration: Overhang angle should not exceed 45° without support
• Example: A 30mm × 30mm × 15mm wedge creates a 45° ramp

7. Pyramid

• Parameters: Base Width, Base Depth, Height
• Best For: Decorative tops, structural points, connectors
• Print Consideration: Steep angles need support; minimum base 10mm
• Example: A 20mm × 20mm × 15mm pyramid creates a pointed decorative element

Height-to-Diameter Ratios for Stability

For vertical structures (posts, towers), maintain proper proportions to ensure printability:

Structure Type	Ideal H:D Ratio	Example Dimensions	Stability Notes
Sturdy Post	3:1	10mm diameter, 30mm height	Reliable; minimal support needed
Tall Tower	5:1	8mm diameter, 40mm height	Requires base reinforcement
Slender Needle	10:1	3mm diameter, 30mm height	High risk; needs support structure

Overhang Angles & Support Structures

Overhangs are surfaces that extend beyond their support. The angle matters:

• 0–45°: Prints reliably without support
• 45–60°: May need support depending on material
• 60°+: Requires support structure

Pro Tip: Design to minimise overhangs. A 30° angle prints cleanly; a 60° angle requires support material that wastes filament and time.

Practical Project: Desk Organizer

Let's combine shapes into a functional design: a desk organizer with compartments.

Design Specifications

• Overall Dimensions: 100mm × 60mm × 40mm
• Wall Thickness: 2mm (PETG for durability)
• Compartment Tolerance: 0.3mm clearance

Step-by-Step Construction

1. Create Base: Cube 100mm × 60mm × 2mm (bottom)
2. Create Main Body: Cube 100mm × 60mm × 38mm (walls)
3. Create Dividers: Three cubes 2mm × 60mm × 36mm, positioned at 25mm, 50mm, 75mm along X-axis
4. Combine All: Select all pieces and group (Ctrl+G)
5. Create Hollow Interior: Add a cube 96mm × 56mm × 36mm, position it centered inside, and use the "Hole" function to subtract it

Tolerance Calculations

If you're designing compartments for specific items:

• Clearance Formula: Desired Width + 0.3mm (for PETG)
• Example: A pen that's 8mm wide needs a 8.3mm compartment
• Adjustment: For PLA (more forgiving), use 0.5mm clearance

Wall Thickness Requirements by Material

Matériau	Minimum Wall Thickness	Recommended Wall Thickness	Best For
PLA	1.5mm	2–3mm	Prototypes, decorative parts
PETG	2mm	2.5–3mm	Functional parts, tools
TPU	2mm	3–4mm	Flexible parts, seals, grips
ABS	2mm	3mm	High-strength parts

The "Hole" Function: Subtractive Design

To create hollow sections, use TinkerCAD's "Hole" function:

1. Create the outer shape (e.g., a cube for your organizer body)
2. Create the shape you want to remove (e.g., a smaller cube for the hollow interior)
3. Select the inner shape
4. Click Edit → Make a Hole (or right-click and select "Make a Hole")
5. Select the outer shape
6. The inner shape is now subtracted from the outer shape

Assembly Tolerances

When designing parts that fit together:

• Sliding Fit (loose): 0.5mm clearance
• Normal Fit (snug): 0.2–0.3mm clearance
• Tight Fit (press-fit): 0mm clearance (parts press together)

Example: If you're designing a shaft that fits into a hole, and the shaft is 10mm diameter, the hole should be 10.3mm for a normal fit.

Common Design Mistakes

Mistake	Problem	Solution
Walls too thin	Parts break during printing or use	Increase minimum wall thickness to 2mm
Overhangs too steep	Poor surface quality, sagging	Redesign to keep angles below 45°
Tolerances too tight	Parts don't fit together	Add 0.3mm clearance minimum
Unsupported tall structures	Warping, collapse during print	Add base reinforcement or support structures

Key Takeaways

• Master the seven essential shapes and their parameters
• Maintain proper height-to-diameter ratios for vertical structures
• Keep overhangs below 45° to avoid support material
• Use wall thickness of 2–3mm for reliable prints
• Apply tolerance calculations for parts that fit together
• Use the "Hole" function for subtractive design

Next in the series: Creating Holes & Subtractive Design – Advanced Techniques